-40%
Norton Cut-off wheels and cut-off wheel supports for surface grinder
Norton Cut-off wheels and cut-off wheel supports for surface grinder
Norton Cut-off wheels and cut-off wheel supports for surface grinder
Norton Cut-off wheels and cut-off wheel supports for surface grinder
Norton Cut-off wheels and cut-off wheel supports for surface grinder
Norton Cut-off wheels and cut-off wheel supports for surface grinder
Norton Cut-off wheels and cut-off wheel supports for surface grinder
Norton Cut-off wheels and cut-off wheel supports for surface grinder
Norton Cut-off wheels and cut-off wheel supports for surface grinder
Norton Cut-off wheels and cut-off wheel supports for surface grinder
Norton Cut-off wheels and cut-off wheel supports for surface grinder
Norton Cut-off wheels and cut-off wheel supports for surface grinder

Norton Cut-off wheels and cut-off wheel supports for surface grinder

$ 66

Availability: 100 in stock
  • Brand: Norton
  • All returns accepted: ReturnsNotAccepted
  • Condition: Three of the non-reinforced cut-off wheels are new, the other three are used. The hardened steel supports where made in my machine shop and are in very good condition.

    Description

    Large lot of cut-off wheels and cut-off wheel supports for use on a conventional surface grinder.
    This lot contains the following:
    Cut-off Wheels: (six total, all Norton, and all with 1.25" center mounting hole)
    There are two Norton reinforced cut-off wheels, .060 thick x φ6.6" OD, wheel spec is A60-OBNA2.
    There are three new, non-reinforced Norton cut-off wheels (also known as rubber wheels), .020" thick x φ6.0" OD,  Norton spec 57A90-ROR30.
    There is one non-reinforced Norton wheel, same spec as previous, but condition is used and OD measures φ5.3".
    Finally, there is a used diamond cut-off wheel, Norton spec ASD100S-R100B90, wheel is φ6.0" OD x 1mm thick. This wheel works, but is a bit "tired".
    Wheel supports: (three sets of wheel supports, all with φ1.25" center mounting hole).
    There is one set of shop made wheel supports, φ1.25" center mounting hole, φ4.7" OD x 0.275" thick, made from 440-C stainless steel, hardened and ground. Excellent support
    when using new, or larger cut-off wheels.
    There is one set of shop made wheel supports, φ1.25" center mounting hole, φ3.7" OD x 0.25" thick, made from 440-C stainless steel, hardened and ground. Excellent support
    when using used, and slightly smaller cut-off wheels.
    Then there is a special set of wheel supports. Custom made by a manufacturer of extremely thin diamond slitting saws. This set is alum, and measures φ5.75" OD x about 0.350" thick. This was designed to support a diamond slitting saw with a φ4.5" ID. To use with cut-off wheels with a φ1.25" center mounting hole, you'll need to mount this in a lathe and remove the raised center section, (its the area marked "back flange")  down below the face of the outer ring.
    Cut-off wheels work best, and can cut very accurately, when supported correctly. Especially when using the non-reinforced wheels, supports are a must. This is an excellent set of supports for use in the toolroom. Supports should also be used with diamond cut-off wheels to extend their life and improve productivity.
    To all potential buyers: Please carefully examine all photos in this listing, this is exactly what you are considering buying. I always try to describe defects or issues in the item description, but photos can be of tremendous help in determining if my item fits your needs. You of course are always welcome to send me questions if you need more information.
    A word of caution regarding the rubber cut-off wheels. I really liked these wheels, they cut without creating a lot of heat and can cut very accurately when supported correctly.
    But, they are not reinforced, so they should be used for thin sections and light duty work. No deep cuts on rough work or they will fail. Thin cut-off wheels not only cut-off, but can also produce thin slots in work.  But use these at your own risk.